« previous next »
Pages: [1]   Go Down

Author Topic: I have an a112 abarth engine....  (Read 7595 times)

0 Members and 1 Guest are viewing this topic.

Offline hermanzini

  • 1300 cc
  • *****
  • Posts: 19
  • Member of Sportsvognslosjen and Scuderia Lazzaroni
    • Hermanzini`s tirekickerpage!
I have an a112 abarth engine....
« on: September 26, 2005, 10:52:53 pm »
Ciao!

Does the a112 abarth engine fit the 600 gearbox?
What modifications must be made?

Thanks!
Logged
scuderia lazzaroni

Offline Brent Mills

  • 1300 cc
  • *****
  • Posts: 13
  • 500
Re: I have an a112 abarth engine....
« Reply #1 on: September 27, 2005, 07:10:14 am »
It'll mate up fine....I wouldn't mind doing this too if I could find a reasonable bottom end.
Logged

Offline abarth695

  • 695 cc
  • ***
  • Posts: 2
  • Abarth 695 SS Assetto Corsa
Re: I have an a112 abarth engine....
« Reply #2 on: October 06, 2005, 02:43:38 pm »
Quote from: hermanzini on September 26, 2005, 10:52:53 pm
Ciao!

Does the a112 abarth engine fit the 600 gearbox?
What modifications must be made?

Thanks!
The only modification is to take off 1 cm from the gearboxaxle.
Logged

Offline hermanzini

  • 1300 cc
  • *****
  • Posts: 19
  • Member of Sportsvognslosjen and Scuderia Lazzaroni
    • Hermanzini`s tirekickerpage!
Re: I have an a112 abarth engine....
« Reply #3 on: October 06, 2005, 10:38:24 pm »
Thanks alot for the good answers!
Logged
scuderia lazzaroni

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: I have an a112 abarth engine....
« Reply #4 on: October 07, 2005, 08:58:30 am »
always kontrole when engine is in  that the flywheel is  not stopt in bellhousing .With the old  fiat 600 you can have problems and you must take some material form it on inside where it is market
Logged
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline hermanzini

  • 1300 cc
  • *****
  • Posts: 19
  • Member of Sportsvognslosjen and Scuderia Lazzaroni
    • Hermanzini`s tirekickerpage!
Re: I have an a112 abarth engine....
« Reply #5 on: October 20, 2005, 03:58:24 pm »
Thanx for the tips guys!
Will it handle the extra power from this awesome engine?
Logged
scuderia lazzaroni

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: I have an a112 abarth engine....
« Reply #6 on: October 20, 2005, 09:04:24 pm »
yes ,I go till  150=====hP form a 2000 cc to it
Logged
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline ChrisD

  • 2000 cc
  • *******
  • Posts: 156
Re: I have an a112 abarth engine....
« Reply #7 on: March 12, 2006, 09:29:57 am »
I recentlly installed an A112 engine to my 600. I cut of 1cm from the gearbox axle and the engine fitted just fine. I used Fiat 600 flywheel, cluch disk and preasure plate but the engine spins. One possibility is that my cluch disk is not new (but it is not for trash too). I have ordered a new set of cluch disk, preasure plate and bearing to install and I hope that it will make the problem go away.
Any other ideas or sugestions of what to do if the problem is not the cluch disk??
Logged
Fiat 600 Abarth

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: I have an a112 abarth engine....
« Reply #8 on: March 12, 2006, 10:31:27 am »
you can use one from some 850 our 126 bis     ,170 mm  our you can also place stronger springs(from valves inside the mechanic)I use now A112 all and take a VW starter with adaptor plate
Logged
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline ChrisD

  • 2000 cc
  • *******
  • Posts: 156
Re: I have an a112 abarth engine....
« Reply #9 on: March 13, 2006, 09:43:31 am »
THe 850 cluch disk and preasure plate is the same with the 600? The guy in my local parts shop told me that they are not the same and I can not use them. And he only sales Fiat parts (so I guess he knows). I use the standar Fiat 600 starter and it didn't seem to have a problem. I will see how the car will roll with the new 600 parts installed and let you know.
Quote from: guy moerenhout on March 12, 2006, 10:31:27 am
you can use one from some 850 our 126 bis ,170 mm our you can also place stronger springs(from valves inside the mechanic)I use now A112 all and take a VW starter with adaptor plate
where excactly do you mean? Do you have a picture of that convertion?

Thanks for the tip
Logged
Fiat 600 Abarth

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: I have an a112 abarth engine....
« Reply #10 on: March 13, 2006, 10:04:36 am »
the are some mechanic  850 our latest seat 750 in 160/170 that fit on flywheel from 600.Our you must drill the holes in correct place. If you use standaard 600 you will have problems
Logged
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline ChrisD

  • 2000 cc
  • *******
  • Posts: 156
Re: I have an a112 abarth engine....
« Reply #11 on: March 13, 2006, 10:40:54 am »
So, if I got it right, I use Fiat 850 cluch disk 160 or 170mm and standard Fiat 600 preasure plate and flywheel, right?
Logged
Fiat 600 Abarth

Offline ChrisD

  • 2000 cc
  • *******
  • Posts: 156
Re: I have an a112 abarth engine....
« Reply #12 on: March 13, 2006, 11:02:37 am »
The Fiat 600 multipla uses the same cluch with the Fiat 600?
Logged
Fiat 600 Abarth
Pages: [1]   Go Up
« previous next »
 

Digital2