Author Topic: Advise on A112 70HP+40DCOE  (Read 24140 times)

0 Members and 1 Guest are viewing this topic.

Offline bibito

  • 1800 cc
  • ******
  • Posts: 44
Advise on A112 70HP+40DCOE
« on: August 27, 2009, 12:30:31 pm »
Hello, everyone,
recently decided to go with the weber 40dcoe on the standart A112
abarth 70HP engine.
Please, advise need adjsutsments and possible pros and cons of that set up.
Thank you.
Lubo
« Last Edit: August 27, 2009, 02:39:47 pm by bibito »

Offline Pantdino

  • 2000 cc
  • *******
  • Posts: 316
  • 500
Re: Advise on A112 70HP+40DCOE
« Reply #1 on: August 31, 2009, 04:03:46 am »
Hello, everyone,
recently decided to go with the weber 40dcoe on the standart A112
abarth 70HP engine.
Please, advise need adjsutsments and possible pros and cons of that set up.
Thank you.
Lubo

I don't recall seeing a 40DCOE on a 4 cylinder engine with the standard Autobianchi A112 / Fiat 850 style single inlet head. Those are usually seen on "4 canal" heads, either Abarth, Aztek, or other aftermarket type, and use 2 of them.

Does someone make an intake manifold for that?

I saw one on an Abarth 695 motor and 2 liter Alfas run a pair of them, so it should work.  But you'll probably have to put the car on a chassis dyno and have someone who knows Webers well do the venturi, jets, and airs to make it run right.

Jim Oddie

Offline Carlos

  • 1000 cc
  • ****
  • Posts: 8
Re: Advise on A112 70HP+40DCOE
« Reply #2 on: August 31, 2009, 10:59:56 am »
Hello pantdino!

Have a look on this side!
newbielink:http://www.abarth-motorsport.nl/ [nonactive]
There you can find inlets for one 40DCOE!

Greatings
Carlos

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: Advise on A112 70HP+40DCOE
« Reply #3 on: September 01, 2009, 08:39:00 am »
a intake manifold of this type was made for the A112 like one piece valvevover/intake on the 58 hp.The difference with a single one is only 2 our 3hp but easy regulation.On the old mini you have the same set.You can better play with the venturis.But fuel becomes hotter and for this the changes it back.Hot fuel =loosing power and vaporlook but is a nice looking set and drives very good.
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline Paul vander Heyden

  • 2000 cc
  • *******
  • Posts: 179
    • Scuderia Topolino
Re: Advise on A112 70HP+40DCOE
« Reply #4 on: September 02, 2009, 01:21:36 am »
I have tried using a single side draft Weber on several customer engines, and I have NEVER made more (usually less) HP than with a two barrel downdraft carburetor.  The preferred down draft is a 36DCD7, although I have also done successful installations of 38DCNF, 40 DCNF and Solex CCI 40-42.

I have intake manfolds to suit any of these carburetor combinations.

Paul Scuderia Topolino
www.scuderiatopolino.com

Offline bibito

  • 1800 cc
  • ******
  • Posts: 44
Re: Advise on A112 70HP+40DCOE
« Reply #5 on: September 02, 2009, 10:04:39 am »
Thank you, Paul, Guy,
the reason beening that it looks better and should perform about the same, + a have a few of those/40dcoe/  I have to use. ;-)
Any ideas on the ventury and jet sizing, cams..
Paul perhaps you have a cam to suit.... ? and I still plan on getting those ARP's...from you
so might just combine them, so if you have any ideas pleas,share.
Thank you,
Lubo 

Offline zippyfiat

  • 2000 cc
  • *******
  • Posts: 185
  • 500
Re: Advise on A112 70HP+40DCOE
« Reply #6 on: September 03, 2009, 07:52:12 pm »
Hi Lubo,

I have had a few people tell me that they tried the sidedraft Weber DCOE only to find that the engine ran poorly after ("like crap" according to one).  They all said they immediately switched to downdraft carbs and the engines ran much better.  The DCOE sure looks good but you should be prepared to be disappointed with the results.  The design of the stock Fiat cylinder head just does not work well with a sidedraft carb. 

You can still find a DCD carb with a bit of patience, but finding a "correct" older version (eg., DCD7) can be harder.  You could always try a DCNF as Paul suggests.

Gil

Offline Pantdino

  • 2000 cc
  • *******
  • Posts: 316
  • 500
Re: Advise on A112 70HP+40DCOE
« Reply #7 on: September 08, 2009, 03:45:08 am »
Hi Lubo,

I have had a few people tell me that they tried the sidedraft Weber DCOE only to find that the engine ran poorly after ("like crap" according to one).  They all said they immediately switched to downdraft carbs and the engines ran much better.  The DCOE sure looks good but you should be prepared to be disappointed with the results.  The design of the stock Fiat cylinder head just does not work well with a sidedraft carb. 

You can still find a DCD carb with a bit of patience, but finding a "correct" older version (eg., DCD7) can be harder.  You could always try a DCNF as Paul suggests.

Gil

Anyone know why a side draft does not work well?
I have read that the fuel has to make a sharp turn, which is a problem.

Also, having a long distance between the throttle butterfly and the intake valves will tend to tune the engine for lower- rev operation, which is not where these engines make power.

Jim

Offline zippyfiat

  • 2000 cc
  • *******
  • Posts: 185
  • 500
Re: Advise on A112 70HP+40DCOE
« Reply #8 on: September 08, 2009, 11:47:21 pm »
Jim, I think that is a question that Paul would be a good one to answer.  I believe the reason is that because of the extra 90 turn and longer runner the fuel does not stay in suspension properly.  I think that by the time the fuel/air gets into the combustion chamber there is actually gas in liquid form that washes onto the surfaces of the chamber.  I might be somewhat off on this, but it's something like that.

To compound the problem, with the design of the Fiat head, cylinders 1 & 4 always run leaner than 2 & 3 because of the extra distance the fuel/air mix has to travel.  It is my understanding that a sidedraft carb. only makes this situation worse.  PBS used to make their "stager" cams to delay the fuel charge getting to cylinders 2 & 3.

The only successful application of sidedraft carbs is with two sidedraft carbs.  These setups (PBS, Abarth OTR for example) have intake runners that are quite short and are of equal length to each cylinder.  There have been some heads where people have welded up the stock opening and added 4 new ones for dual carbs along with a custom intake manifold.  I've seen 2 or 3 of those on ebay in Germany in the past few years.

Maybe some expert out there will correct what I've said or add to it.....

Gil

Offline bibito

  • 1800 cc
  • ******
  • Posts: 44
Re: Advise on A112 70HP+40DCOE
« Reply #9 on: September 10, 2009, 04:11:13 pm »
Thank you, Gil,Jim,
for shearing your thoughts.... but still,
is there anyone, in the forum, that has been or still is using that set up?
I already got the manifold , so I guess I'll have to give it a try, any practical tips will be welcomed thou.

Lubo

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: Advise on A112 70HP+40DCOE
« Reply #10 on: September 10, 2009, 04:46:37 pm »
I use it on a 850 spider and works very well.Use very small chokes 25 our 28 .The adventage from this set is that you can find all parts easy for a 40 Dcoe.Start with 125 /190.Think on a NSU 1000 TT our TTS,this have also very long and high intakes.Also the first prototype  A112 (with TCR head)had long intake manifold and over the engine.
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline bibito

  • 1800 cc
  • ******
  • Posts: 44
Re: Advise on A112 70HP+40DCOE
« Reply #11 on: September 11, 2009, 05:19:04 am »
Hi, Guy,
I have the manifold with holes for 38mm, I guess 38DCOE,
should I be looking for a 38DCOE or just use 40 and change the chokes and jets accordingly.
Could you please, post some pictures of your car with that set up.
Thank you,
Lubo

Offline guy moerenhout

  • Administrator
  • 3000 cc
  • *****
  • Posts: 4.492
    • www.abarth-gmr.be
Re: Advise on A112 70HP+40DCOE
« Reply #12 on: September 11, 2009, 08:40:32 am »
you can open the holes to 40.The 38 dcoe was use on fiat 2300 S.Car is sold .A populair set for the A112 first serie was a intake manifold and valvecover in one piece for the DCOE.
______abarth  gmr-team ______
___http://www.abarth-gmr.be ___

Offline grant gauld

  • 2000 cc
  • *******
  • Posts: 146
Re: Advise on A112 70HP+40DCOE
« Reply #13 on: September 11, 2009, 03:06:05 pm »
I also made a 40 DCOE to work very well on a 850 sports motor (903cc).The car won its class in a few hillclimbs and a 4 day classic rally.You just have to find someone who is genuinely skilled at jetting when you run the motor on the rolling road.I made a large kidney shaped inlet port in the head,about 75% larger (to suit the manifold).
 I think I have tried 5 different carbys and I do prefer a 36/36 DCD,but if its what you want,go for it.
 A pretty common cam grind like a 30/70/70/30 worked well with the DCOE.If you can reduce your cars weight this will also make a very big difference.
Grant

Offline trevor

  • 1800 cc
  • ******
  • Posts: 96
Re: Advise on A112 70HP+40DCOE
« Reply #14 on: September 12, 2009, 04:56:34 am »
Re Guy's comment (reply #11) re A112 with TCR head; see photo; one wonders how vibration effect on dcoe's was controlled, if possible ?
Trevor

 

Digital2